What a warehouse lighting requirement should identify
The task and the receiving surface
A warehouse lighting brief should identify what people must see and where the light needs to arrive. Reading a small label on a rack is a different task from moving a large carton across an open floor. Both can occur under the same high bays, but they do not necessarily share the same receiving surface or lighting criterion.
Describe the task before choosing a number. Include the label size or work detail that matters, the normal viewing position and anything that obstructs the light path. This gives the lighting comparison a purpose beyond making the building look bright.
A value with a source and scope
A useful requirement states the quantity, unit, receiving plane and evaluation basis. It also identifies who set it and which activity or jurisdiction it concerns. A value copied from an online chart may leave most of these fields unspecified.
For example, an average illuminance target for a packing worktop needs a different report entry from a minimum value along a route. Keep those objects separate in the brief. The product proposal can then answer a defined question instead of choosing a convenient number after the fixture has already been selected.
Safety rules, design recommendations and project targets
Jurisdiction and work activity
Published lighting figures can come from different kinds of documents. A legal minimum has an applicability context; a professional recommendation supports design; a customer specification sets the agreed project task. Identify that role before using the figure to accept or reject an offer.
For instance, OSHA 1926.56 is a construction illumination rule. Its table includes an indoor warehouse entry within that context. The word โwarehouseโ does not turn that construction table into a universal design specification for every operating storage facility.

Read the document heading as well as the row containing the familiar activity name. Construction work, a special industrial activity and normal building operation can fall under different provisions. A chart that removes the heading can make an accurately copied number misleading in a new context.
The same care applies to a customer specification. It may set a higher or more task-specific target than a safety minimum. That target can still be the contractual comparison basis for the proposal, provided its scope and origin are clear.
Who established the project criterion
Washington's WAC 296-800-21005 expressly describes safety minimums and separates activity categories, averages and individual measurements. Those distinctions matter when reading that state's rule. They should remain attached to it when discussing its values.
The IES public description of RP-7-21+E1 identifies warehouse and storage lighting within its industrial-lighting scope. Its public contents include horizontal and vertical illuminance. To compare a claimed IES value, identify its cited edition and applicable task criteria. A seller's summary can leave out those conditions.
For a binding project requirement, the applicable authority or qualified project professional needs to establish the scope. The buyer's immediate job is to retain that scope when requesting and comparing a lighting proposal.
Light levels for storage, picking and packing
Labels on rack faces
Picking work often involves a vertical target: a carton face, shelf label or location marker. The light reaching that target depends on its orientation and the space around it. Light landing on the tops of racks does little for a label facing the aisle below.
The amount of detail also changes the task. Large contrasting location markers and small low-contrast product text are different viewing problems. Describing them as one general storage task can hide the reason a picker still struggles after a brighter fixture is installed.
Horizontal work surfaces
Packing, checking and sorting take place on horizontal surfaces at their actual working height. A floor result may describe the circulation area but leave the worktop unresolved. Equipment or a worker's body can also affect the light arriving on a bench.
| Zone or task | Receiving surface to identify | Detail that changes the brief | Comparison record to request |
|---|---|---|---|
| Rack picking | The label or product face | Text size, contrast and shelf position | Result on the relevant vertical surface |
| Packing | The actual worktop | Small print, sorting or inspection detail | Result on the named horizontal work plane |
| Open storage | The surface used for the stated activity | Large cartons versus finer identification | Result for that zone and its defined plane |
| Circulation | The relevant route or surface | Obstructions and the operating task | The quantity and criterion required for that route |
This record helps distinguish a difficult task from a request for more lumens everywhere. Where a localized task needs additional treatment, compare that option with increasing the output across the whole building.
Lux, foot-candles and the stated measurement plane
Convert the unit without changing the criterion
Lux and foot-candles both describe illuminance: light arriving on a surface. Washington's official note gives the conversion of one foot-candle to 10.76 lux. Using that rounded factor, 20 fc converts to 215.2 lx.
That calculation is a unit example, not a recommended warehouse target. Converting the unit leaves the underlying plane, statistic and operating condition unchanged. A vertical average expressed in foot-candles remains a vertical average when expressed in lux.
Emitted lamp or luminaire lumens have a different role. Dividing those lumens by room area does not, by itself, establish the illuminance on the task. The actual light distribution, geometry and relevant losses still affect where the light arrives.

Floor, workbench and vertical rack face
State the plane in a way that another person can locate it. โAt the workbenchโ is more useful when the bench height and task area are identified. A rack-face result should identify which face and height range the comparison concerns.
Look for the same information on a proposal or calculation. If the drawing shows a horizontal plane across the room, it cannot silently stand in for a vertical rack calculation. Comparing these records accurately can prevent the wrong design revision being requested.
Average, minimum and uniformity answer different questions
Averages can hide a local shortage
An average condenses values across an area. Some locations can be above it and others below it. Whether those local differences matter depends on the task and the agreed criterion.
Read the minimum result where the brief requires it. A sufficiently high average cannot answer a separately specified minimum. Likewise, a minimum value without the defined calculation area provides an incomplete description of the space being evaluated.
Ratios need a definition and the same plane
Uniformity can be expressed with different ratios. Minimum divided by average and average divided by minimum move in opposite numerical directions. Keep the definition beside the value so that two reports can be compared correctly.
The underlying surfaces also need to match. A ratio for an open floor says little about variation along a vertical rack face. When a proposal uses several calculation planes, follow the criterion attached to each one rather than choosing the most favorable statistic from the whole report.
As a separate arithmetic illustration, suppose the average on one defined plane is 200 lx and the minimum on that same plane is 80 lx. The minimum-to-average ratio is 0.40; the average-to-minimum ratio is 2.5. Both describe the same two assumed values. Comparing either number with an unlabeled ratio from another offer could reverse the meaning of the result.
Neither ratio is an acceptance recommendation here. The relevant point is to preserve the definition, area and plane. If a target requires one convention, calculate or request that convention on the matching result rather than judging the proposal by the most favorable-looking number.
Maintained lighting and changes to the warehouse
Aged or dirty equipment and changing surfaces
An initial lighting result concerns a stated starting condition. A maintained-lighting target concerns the result after the relevant changes allowed for in the design. The assumptions behind that allowance should be visible in the proposal.
Dust on optical surfaces, aging equipment and changes to room surfaces can affect the light available for work. The amount depends on the installation and its maintenance arrangements. A cleaning interval or maintenance factor copied from another building can misrepresent that basis.

| Report field | What it helps establish | What needs to match the brief |
|---|---|---|
| Average illuminance | The area's stated average result | Area, plane, operating basis and target |
| Minimum illuminance | The lowest reported value on that area | Area definition and the required minimum criterion |
| Uniformity | The stated relationship between reported values | Ratio definition and the same receiving plane |
| Initial or maintained basis | The condition represented by the result | The stated losses, maintenance assumptions and evaluation point |
New racks and a different visual task
A rack change can alter both the target and the light path. A product line with smaller labels can also change the visual task even when the room dimensions remain the same.
Review the affected zone rather than assuming the old result still describes the operation. VST's published warehouse high-bay page provides a product route for this discussion, while the task brief establishes what the selected product needs to achieve.
Build a three-zone requirement brief
State three assumed customer targets
Consider a hypothetical warehouse brief with three specified average targets: 100 lx on an open-storage horizontal plane, 150 lx on the rack-label vertical plane and 300 lx on a packing worktop. These are assumed project inputs for this example, not legal or IES recommendations.
The brief identifies each zone and its surface separately. It also records that no minimum or uniformity criterion has yet been supplied for this illustrative exercise. That prevents an average-only comparison being described as a complete lighting acceptance.
Put each target on its proper surface
An initial offer reports a room-wide horizontal average. That result alone leaves the three-zone comparison incomplete: the areas and planes have not been matched to the brief.
The comparison then obtains separate, explicitly hypothetical results for the named surfaces: 120 lx for storage, 90 lx for rack labels and 340 lx for packing. These figures are illustrative report inputs, not a simulated VST installation or measured project.
Read the result of a mismatched report
The storage and packing averages now exceed their assumed average targets; the rack-face average falls below its target. Increasing the room-wide average is not the only response to investigate. The rack result calls for attention to the light arriving on that vertical surface.
That is a useful decision even before selecting a final fixture arrangement. It identifies the part of the proposal that needs revision and avoids treating the two adequate average results as proof that the whole brief has been met.
The mismatch also changes the purchasing discussion. Replacing every fixture with a higher-output unit might raise the two already adequate averages and still leave the rack arrangement unresolved. A review of the optical version or the location of light relative to the labels is a more focused next comparison.
The example does not prescribe that design change. It gives the buyer a reason to evaluate it: the deficient result belongs to a named vertical surface, while the storage and packing results already satisfy the assumed average inputs. That is more useful than describing the warehouse simply as too dark or asking for the brightest fixture.
Use the brief to compare a high-bay proposal
Matching photometric configuration and calculation surfaces

The light-distribution file must correspond to the proposed model, optic and operating configuration. A file for another version may describe a valid product but answer the wrong comparison.
Then follow the calculation surfaces. Match the zone, orientation and relevant height to the brief. Read the reported statistics and stated initial or maintained basis together. This approach makes a discrepancy specific: the wrong plane, a missing zone result or an unfulfilled target.
Keep fixture-count arithmetic in the high-bay quantity calculation where it is needed. Establishing the target and estimating the quantity are related tasks, but the first cannot be replaced by the second.
When local or task lighting is the relevant alternative
If the packing work demands a different light direction or a more localized treatment, compare that approach with changing all the high bays. Include the effect on access, controls and the actual task surface.
Similarly, an aisle with tall racks may need a different distribution from the adjacent open area. The brief lets the proposal distinguish those tasks instead of assigning the entire warehouse one output level.
A clear requirement is a better comparison basis
Carry the task, plane and source together

| Assumed zone | Assumed average target | Illustrative matching result | Result of this comparison |
|---|---|---|---|
| Open storage | 100 lx, horizontal | 120 lx on the named storage plane | Meets this assumed average target |
| Rack labels | 150 lx, vertical | 90 lx on the named rack face | Needs revision for this task |
| Packing | 300 lx, horizontal worktop | 340 lx on that worktop | Meets this assumed average target |
The table resolves only the average criteria stated in the example. A complete project still needs its applicable requirements and any other agreed evaluation criteria. A clear brief carries the task, receiving plane, quantity and source together, making both the proposal and its remaining gaps easier to assess.