A 400W metal-halide marking identifies the old lamp, but it does not identify the power of the complete fitting or the light that arrives on a warehouse floor. Replacing that installation with LED involves a physical choice as well: keep a suitable host with an approved lamp or kit route, or replace the whole luminaire.
Begin with the retained assembly and the task it serves. Compare output and distribution at the work surfaces, then calculate energy using complete-system input power. A lower LED wattage is a possible result of the selection, not a universal replacement rule.
What does the existing 400W marking actually identify?
Lamp power and whole-system input
The metal-halide lamp is one component. Its ballast and the rest of the operating arrangement affect complete-system power. A 400W lamp therefore does not prove the installed luminaire draws exactly 400W. Record or obtain the relevant complete-system input for the actual gear before using an energy estimate. If the ballast identity or input is unknown, keep the starting point as unknown instead of borrowing a fixed percentage from another project’s fixture.
That distinction affects a warehouse with many fittings. An error of a few dozen watts per installed system is multiplied by operating hours and quantity. It can make a payback spreadsheet look more precise than the site information warrants. The example later in this article labels its entire old-system input as an assumption; it is not a measurement from a VST customer.
Condition and age change the lighting baseline
The current room appearance may reflect an aged lamp, a dirty reflector or a changed warehouse layout. It is not automatically the light level the replacement should copy. Decide which tasks the updated installation must serve: floor travel, handling, rack-face labels or detailed inspection. Evaluate the old housing separately for physical integrity and optical usefulness. A favorable new-lamp datasheet cannot make an unsuitable host into a sound luminaire.
Describe the light task before comparing LED offers
Where the output must go
A fixture above open staging space has a different job from one above tall shelving. Workers may need light on the floor and on vertical labels. Record the actual mounting positions, the affected work surfaces and the normal viewing directions. That lets the next comparison ask whether a proposed LED assembly delivers useful light at those places, rather than whether its marketing page claims to replace a 400W lamp.
As a first pass, keep the number of existing luminaires and their zones on the survey. That quantity helps define access and work scope. It should not become the final LED fixture count before the optical distribution and task are known. If current positions are blocked by racks or equipment, a new fixture may need a different layout even where a lamp replacement fits the old socket.
Original host and future maintenance
Note whether the existing reflector, lens, enclosure and support are sound. A lamp-only proposal relies on more of them than a complete replacement does. A kit may retain a usable housing but replace the light engine and electronics. Facilities teams should also know what replacement component they will stock afterward. The word “retrofit” is too broad to answer that maintenance question on its own.
Three physically different routes from a metal-halide high bay
Reuse a suitable host
An LED replacement lamp can be considered only when the selected product is intended for the identified host and its operating arrangement. The old socket, reflector, temperature environment and instructions all matter. A bulb that fits mechanically is not enough information to treat the conversion as approved. A host-specific LED retrofit kit is another route: it may retain the housing while changing internal parts under the kit’s stated scope.
In the United States, UL Solutions explains how certified luminaire retrofit kits identify suitable host types, kit parts, instructions and field labels. That explanation concerns the applicable kit and installed host, not a certification granted to an arbitrary LED component or VST product. A qualified person must assess any actual conversion against the current instructions and local requirements.
Replace the complete luminaire
A finished LED high bay brings its own housing and optic. It is a reasonable direction when the old enclosure is unsuitable or when a different optical layout is needed. It also changes the bill of materials: the project is purchasing a new assembly and the work to remove the old one. Its fit to the building support and electrical supply still needs to be established; a replacement fixture is not a reason to ignore either.
| Route | Existing equipment retained | Decision-critical evidence |
|---|---|---|
| LED lamp conversion | More of the original housing, optical and support system | Exact lamp instructions, host suitability and operating arrangement |
| Applicable retrofit kit | Only the host parts identified for that kit | Kit identity, eligible host and conversion instructions |
| New LED luminaire | Building position or support only where suitable | New assembly data, optical task fit and actual work scope |
Compare maintained task light, not nameplate watts
Initial output and the old optical system
The original MH lamp’s initial lumen value is not the installed light reaching every task. The reflector redirects light, the cover can change distribution, and output can change with condition and use. LED luminaire lumens also describe emitted light rather than the result at a rack face. Compare equivalent receiving surfaces, operating conditions and the assembly being offered. A vendor’s “400W equivalent” tag is a starting search cue, not a measured room replacement.
A new LED optic may direct more of its output toward the intended task, or it may miss an important vertical surface. An older fitting with a reflector can distribute light differently again. Without corresponding photometric records or relevant observations, ranking two LED fixtures only by total lumens is not a lighting decision. Record whether the project is preserving current task light, correcting an underlit area or changing the room layout.
What a relevant comparison should show
For an open floor, compare light across the work area and between proposed positions. For racked storage, add the vertical surfaces where labels are read. Include source visibility from normal working angles. The comparison can then show whether a lower-input candidate actually serves the task or simply draws fewer watts. This is the evidence that makes an energy estimate commercially meaningful.
Read the candidate’s exact published output and input
Two VST high-bay records as a shortlist
VST’s VST-HBL-150WF record lists 150W and 22,500 lm at its stated full-power setting. The VST-HBL-200WF record lists 200W and 30,000 lm at its stated full-power setting. Both list 60-, 90- and 120-degree optic choices and a 100-277V AC input. These records provide genuine comparison inputs. They do not establish that either fixture replaces a particular MH installation or that every optic puts the same light on its tasks.
Each family also lists lower DIP power settings. The published full-power lumen number must not be copied into a lower-setting quotation without suitable version data. State the proposed setting, optic and CCT beside the model, so a later sample or bulk order is checked against the same object. The published 500W VST high-bay record, for example, has a different 180-305V AC input range; a series-wide voltage statement would be misleading.
Keep luminaire output and task output separate
The 150W candidate has a lower stated input than the 200W candidate and a lower stated full-power lumen output. Which is useful in this conversion depends on the selected optical configuration and the work area. A facility manager can carry both into a lighting comparison while ruling out any option whose supply range or physical configuration does not match the site. That is a shortlist, not a final wattage substitution.
Does the old housing deserve to stay?
Physical condition and optical purpose
Retaining a host has value only when the parts that remain are suitable. Inspect the condition of the housing, reflector, seals where applicable, socket and support as relevant to the route. The person responsible for electrical or structural assessment must use the applicable equipment instructions. A photograph of a sound exterior will not identify all interior conditions, and a component’s rating cannot automatically approve the assembled fixture.
If the host is physically damaged or its optical arrangement cannot serve the new task, a lamp-only conversion becomes less attractive. A documented kit may still be worth considering where its eligible host is sound and the kit changes the optical parts that need changing. If the host itself is unsuitable, a complete new luminaire is the useful direction. This gives the three routes a conditional result instead of a blanket ranking by unit price.
What a kit record should establish
| Observed or documented condition | Route still worth evaluating | What the condition cannot prove |
|---|---|---|
| Sound host and suitable retained optics | Identified lamp or eligible kit, subject to its instructions | Electrical and optical compatibility of any LED offered |
| Sound host but unsuitable old optical parts | Host-specific kit or a new luminaire | That a replacement lamp alone solves distribution |
| Unsuitable housing or support | Complete luminaire and appropriate new installation plan | Fit, supply and lighting performance of the new unit |
Supply and control needs can change the chosen form
Match the actual input version
The old site supply belongs to the project record. The proposed luminaire needs its own stated input range and installation conditions. On the two cited VST 150W and 200W models, the published 100-277V AC value is a model-field reference. It does not transfer to every high bay VST offers. A facility with another supply range would need a suitable variant or a different documented arrangement, determined by qualified electrical personnel.
Switching is also a use case
Metal-halide operation and an LED system can behave differently when switched or controlled. If the site plans occupancy-based reduction or frequent changes in output, identify the intended control behavior before choosing the LED electronics. A “sensor” or “dimmable” option label does not establish the exact controller, minimum output, restart behavior or energy saved in that building. The separate high-bay dimming guide explains those driver relationships in more detail.
Some warehouses also have dust, washdown, temperature or mechanical exposure requirements. Use the exact fixture’s applicable rating and installation instructions. Do not turn an IP value on a catalog page into approval for an unspecified cleaning procedure, and do not use this article as a connection drawing.
A declared energy example for the complete-fixture route
Project inputs and arithmetic
Take a hypothetical project with 60 existing fittings. Assume their complete old-system input is 460W each, based on a value the hypothetical buyer has declared for this exercise. Assume 3,000 operating hours each year and an electricity rate of $0.16/kWh. The proposed VST 150WF and 200WF candidates are evaluated at their published full-power inputs of 150W and 200W. This is not an actual VST installation, a measured MH ballast load or a finding that both LED options deliver equivalent light.
The assumed old system uses 60 x 0.460kW x 3,000h, or 82,800kWh annually. Sixty 150W luminaires would use 27,000kWh at the same hours; sixty 200W luminaires would use 36,000kWh. The input-energy differences are 55,800 and 46,800kWh. At the assumed tariff, those become $8,928 and $7,488 per year. They are gross electricity differences under the declared inputs. They leave out purchase price, controls, site access, maintenance, tax and changes to the number of fittings.
What makes the comparison usable
The 150W direction shows a larger numerical power reduction, but it is not automatically the better replacement. If its chosen optic and layout miss a task, the facility may need more fixtures, a different setting or another luminaire. Recalculate using the accepted fixture count and actual operating states after the lighting task has been evaluated. The example teaches a whole-system arithmetic method; it does not authorize a blanket 400W-to-150W swap.
Cost and maintenance factors outside the electricity figure
Separate the three purchase scopes
A replacement lamp, an identified retrofit kit and a complete luminaire can have different hardware and labor scopes. An offer that keeps a certified usable host might have less material to remove, but it can leave aging parts to maintain. Another offer may involve substantial access work and supply a new optical assembly. Neither can be priced from the fixture unit amount alone.
When an old HID lamp is removed, the project also needs a lawful route for its material. US EPA describes HID lamps as a mercury-related waste category and directs users to the relevant state environmental agency for disposal requirements. That is a project scope and jurisdiction question, not a universal shipping or disposal instruction.
| Scope item | What the offer should include | Why it can change the decision |
|---|---|---|
| Supplied equipment | Exact lamp, kit or whole luminaire and included parts | Unit prices cover different objects |
| Work at the existing fitting | Qualified labor, access and identified host changes | Retained versus removed parts change hours and work |
| Removed equipment | Handling responsibility and applicable disposal route | Conversion and complete replacement remove different materials |
| Future service | Replacement part, access and agreement coverage | A lamp warranty does not set whole-site maintenance cost |
Select the form that fits the declared project
An assumed unusable host
Return to the hypothetical 60-fitting example. Now assume an assessment finds the existing housings themselves unsuitable to retain. This is a declared condition of the teaching brief, not a story about a customer failure. A lamp conversion or a kit that depends on those hosts no longer solves the physical problem. The complete-luminaire route is the selected form for this brief.
That result does not make the 150W and 200W candidates interchangeable. Their published output and lens choices let the project develop a lighting comparison, while the task surfaces, selected files, layout and supply decide which model can proceed. If neither supplies adequate useful light from the available positions, the project needs another configuration or layout.
What the buyer can do next
The buyer can now ask for a complete new luminaire proposal with the selected output setting, optic, intended position and removal work identified. The VST 150W UFO product page provides one published model direction; a 200W option can be examined when the lighting task calls for another output package. The request is specific because the form decision has already been made.
What must change hands with the converted lighting?
The installed assembly needs an identity that the maintenance team can use. A complete new luminaire has a model and optical/electrical version; an in-host conversion has a different lamp or kit record and any applicable marking. The removal agreement identifies who handles old HID materials.
| Object | Handover record | Who needs it |
|---|---|---|
| New LED luminaire | Actual model, optical/electrical version and mounting description | Facility maintenance and future purchaser |
| Retained/converted host, if used | Eligible kit/lamp identity and applicable instructions and marking | Installer and later relamping staff |
| Removed HID material | Handled items and locally applicable disposal responsibility | Project owner and removal contractor |