24V fixed-white RF kit
Start with 5m of C320W1008 COB tape, a single-channel RF dimmer and handset. Published strip load: 50W. A 60W supply is the initial sizing proposal, subject to its operating limits.
Request This Configuration Complete kit configuration
LED strip lights with remote, receiver and matched power supply
Specify the complete package for handheld dimming, adjustable white or color lighting.
- Choose a fixed-white, CCT or RGBW kit.
- Include the receiver, remote and supply in one component list.
- Match output channels and power to the selected strip length.
- Ask VST for an itemized configuration and sample plan before ordering.
Choose the control function
Order the parts that make the system work
LED strip lights with remote control should arrive as a clearly specified package. A reel on its own leaves the receiver, handset and power source to be selected separately. Start with the required lighting function and include all four in the quotation.
The kit routes below pair published VST strips with receiver and supply requirements. As a remote control LED strip supplier, VST can discuss prepared lengths, matching connections and private packaging around one component list. State the lighting mode, zones and destination plug. The quotation identifies the accessory models and everything included.
A complete component list
List tape, receiver, handset, power supply and installation accessories individually. Include quantities so a quotation for bare tape cannot be mistaken for a kit.
Choose the lighting mode
Fixed white needs a dimming output, CCT needs two white channels, and RGBW needs color channels plus dedicated white. Match the remote to that receiver mode.
Specify the delivery format
Select a reel kit or prepared sections. Identify plug type, cable lengths and packaging before deciding which connections are assembled ahead of shipment.
Matched supply scope
Build the kit around one agreed specification
As an LED strip manufacturer, VST can develop the light-source specification and coordinate the accessory requirements for your requested kit.
An itemized kit quotation
Request separate entries for the light engine, receiver, remote and supply, with manufacturer identifiers recorded before the accessory selection is accepted.
A sample of the whole system
Plan a sample with the selected receiver and power supply as well as the strip. Pairing and operating behavior can then be assessed together.
Connection preparation
Prepared leads and identification can follow the selected interface. Agree these details during sampling to keep the strip-side connection consistent in production.
Communication on substitutions
Replacing a receiver or handset may change pairing and operation. Make proposed substitutions visible before a new batch, so their effects can be checked.
System boundary
How LED strip lights with remote control fit together
The power supply feeds a receiver, and the receiver controls the tape in response to the handset. The selected output mode must match the tape’s white or color channels.
The proposed RF kits use fixed-white, tunable-white and RGBW light engines. RF control suits a receiver positioned out of sight, while an IR alternative needs a clear route to its sensor. Decide on the operating zones before choosing the receiver family. LED strip lights with remote control can be quoted with mounting accessories and prepared connections, but the exact parts and their model identifiers must be fixed for the order. The kit layouts shown are configuration illustrations; the supplied housings and connectors follow the agreed BOM.
Choose your kit
Three complete-package starting configurations
Each route covers tape, an RF receiver, a compatible handset and a power supply. The illustrations show proposed layouts. Request the component models and final BOM in your quotation.
24V tunable-white RF kit
Use 5m of S2835L120CCT1208 for 3000K-6500K adjustment. Specify a two-channel CCT receiver and matching remote. The 60W maximum combined strip load gives a 75W supply starting point.
Request This Configuration 
24V RGBW RF kit
Choose the 24V version of S5050L60RGBW1412 for color plus dedicated white. A 5m run is rated at 72W. Start with a four-channel receiver, RGBW handset and a 96W supply proposal.
Request This Configuration Practical handover
What to record with the kit
An LED strip OEM supplier can help prepare the assembly information for your selected control package.
Labeled Circuit Sections
Label strip sections to match the zone plan. The installer can then identify which physical run belongs to each control output.
Relevant Light Options
Single-color, tunable-white, RGB and RGBW strips have different lighting functions. Select the control channels needed by the strip you choose.
Identified kit components
Record the receiver and handset manufacturer models alongside the strip and supply. A configuration label alone does not identify replacement components.
Order-Specific Packing
Discuss kit packing or grouped parts if sections will go to different installations. Each group should arrive with the documents it needs.
Light-Source components
The light source and the electronics that operate it
Keep each part visible in the kit specification. The selected component models, electrical ratings and connectors should be recorded together.
Component 1
LED light source
The emitters determine which lighting functions are available. Compatible electronics can dim a single-color strip; separate color channels allow their outputs to be mixed. When choosing LED strip lights with remote control, settle the white or color behavior before selecting the handset. A remote with more buttons cannot add a white channel or another color function that the tape itself does not have.
Component 2
RF receiver
The receiver converts handset commands into the output required by the tape. Choose a single dimming channel for fixed white, two channels for CCT or four for RGBW. Check both per-channel and combined load limits at the installation temperature. For LED strip lights with remote control, a matching handset and receiver family are essential; sharing a radio frequency alone does not establish compatibility.
Component 3
Constant-voltage power supply
The supply converts the available input to the strip’s required DC voltage. Size it for the complete connected load and the supplier’s temperature and derating instructions. Our example kit calculations leave capacity above the published strip wattage, but they do not replace the chosen supply’s operating limits. Specify the destination plug or hardwired input and keep the supply accessible after installation.
Company context
Explore the range and the working relationship
Product-category information and cooperation feedback answer different questions about sourcing.
LED strip products as the starting point
The VST category video introduces strip products. Use it to begin a discussion of the light source, then request the receiver, handset and supply in the component list. The kit quotation establishes the exact package.
Communication through the order
Customer feedback provides context for working with VST. For a kit order, agree who supplies each part and how substitutions are handled. Pairing, range and component compatibility are checked on the selected sample package.
Remote-Control applications
Choose LED strip lights with remote control by application
The useful distinction is who operates which zone and what happens when the lighting is switched.
Hotel room coves
In a guest room, handheld dimming lets someone adjust indirect light from the bed or a seat. Decide on startup brightness, a manual way to operate the lights and a place to keep the remote. VST can discuss the strip and itemized control package for the room layout and handover instructions.
Media-wall backlighting
A media wall can use remote adjustment of background brightness or color without opening the cabinet. Locate the receiver, check reflections and decide whether television power switches the lighting supply. We can shortlist strips and discuss service access for the receiver; screen synchronization must be specified separately if you need it.
Display cabinets
Display-cabinet brightness may need adjusting when merchandise or surrounding light changes. Decide whether white-light quality or decorative color takes priority, and whether adjacent cases should respond together. VST can help define the strip sections and zone schedule so the requested remote functions follow the way the cabinets are arranged.
Meeting-room zones
A meeting room may have separate runs over the table, presentation wall and perimeter. Decide which groups need independent adjustment and whether they must work with building controls. Our team can discuss the strip loads and which parts VST supplies before a compatible remote-control method is selected for the room.
Temporary event counters
At temporary event counters, controls need to remain understandable as staff and layouts change. Specify the colors or dimming functions required, access to the receiver and how the parts travel between events. VST can discuss prepared sections and grouped packaging, with the controller chosen to support repeatable setup and handover.
Define your controls
Get one quotation for the complete lighting package
Choose white, CCT or RGBW and send your length, zone count and destination plug. Your remote control LED strip supplier can use that brief to prepare a component list covering the tape, receiver, handset, supply and connection accessories.
Strip-Side reference
LED strip lights with remote: kit BOM and power planning
The table defines proposed kit contents and sizing requirements. Strip specifications come from published VST models; accessory ratings are selection targets until a sourced model is agreed.
| Kit specification | Proposed order requirement |
|---|---|
| Tape quantity | 5m per starting configuration; prepared lengths optional |
| White light engine | C320W1008; 24V; 10W/m; 8mm COB |
| CCT light engine | S2835L120CCT1208; 24V; 6+6W/m; 8mm SMD |
| RGBW light engine | S5050L60RGBW1412; select 24V; 14.4W/m; 12mm SMD |
| RF receiver | 1 per zone; compatible single-white / CCT / RGBW mode |
| Handheld remote | 1 matched handset per kit; zone layout specified |
| Power supply | 1 at 24V DC; initial proposals: white 60W, CCT 75W, RGBW 96W |
| Connections | Strip leads, matching receiver terminals and supply connection |
| Installation pack | Specified clips, connectors and operating instructions |
| RF selection target | 2.4GHz family; actual protocol, range and compliance follow selected models |
Specify reel or cut-section packing, lead length, plug type and private labeling. A kit BOM should name each sourced receiver, handset and supply before sample acceptance. RF range, memory and optional app access are selection items for those components; include any required function in the quotation.
The LED strip factory prepares the tape and connections against the order specification. For a kit, add a sample check of receiver mode, pairing, dimming and restart behavior. Use the accepted BOM for component identification and packing checks, including instructions and any agreed mounting accessories.
Disconnect power before wiring. Match supply voltage, output channels and polarity using the selected component documents. Keep the receiver accessible and fit the strip on a suitable support. Pair the handset using its actual instructions, then test zone selection and recovery after the normal upstream switch is turned off and on.
Working feedback
Clearer decisions across the control package
Good communication makes the supply boundary easier to understand.
Quotation and supply
Ordering LED strip lights with remote control
The agreed bill of materials determines what is sampled, produced and packed.
Arrange a complete kit sample once its component models are selected. Trial the receiver, remote and supply with the intended strip. By agreement, sample costs can be credited toward subsequent bulk production.
A general strip-order starting point is 500 meters. List remotes and receivers separately by kit or zone. The strip quantity does not determine how many control sets the project needs.
Regular products typically require 2-3 weeks of production; light customization is approximately 3-4 weeks and extensive customization approximately 4-6 weeks. Availability of the agreed control components also affects planning. These are production ranges, with transit scheduled separately.
Private labels and custom packaging are available. Instructions must match the selected receiver and remote. Extensive customization may incur tooling charges, which should be identified in the package quotation.
A sample order is prepaid in full through PayPal, Western Union or bank transfer. Normal bulk terms are a 30% deposit and 70% balance before shipment, paid by bank transfer. Use the quotation to establish the total package value.
Specify warranty terms for each part of the kit. Strip coverage is generally two or three years, with five years limited to selected products. The quoted receiver and handset need their own terms. Support quality claims with a description and photos or video.
Control questions
Settle the operating details before ordering
LED strip lights with remote control are easiest to order when the kit contents and electrical load are explicit. These questions cover power calculations, supplied accessories and everyday operation, helping you choose a package that fits the installation before the component models are finalized.
Ask for the strip model and length, receiver model, handset model, supply model and accessory quantities. State plug type, zones and any prepared cable lengths. The quotation should distinguish included installation parts from site-provided channels or wiring and identify the samples used to accept the complete package.
| 5m configuration | Published tape load | Initial supply proposal |
|---|---|---|
| Fixed white | 5 × 10W = 50W | 24V / 60W |
| CCT, both channels | 5 × (6+6)W = 60W | 24V / 75W |
| RGBW | 5 × 14.4W = 72W | 24V / 96W |
Some receiver families support multiple zones. Separate independently controlled rooms from lights that must respond together, then test pairing before handover.
An upstream wall switch cuts receiver power. Check how the chosen controller restarts and whether that behavior suits normal use of the switch and remote.
App access is an additional requirement. It may need a specific receiver, gateway or network connection, so request it explicitly when selecting LED strip lights with remote control.
Check replacement availability and keep both component model identifiers with the pairing instructions. If operation without the remote is essential, specify an alternative control method.