Integrated OEM lighting
This headboard reading light directs an adjustable beam toward the page while keeping the feed behind the furniture. VST is a headboard reading light manufacturer that develops the head, mounting plate and rear cable path together. You receive a mounting sketch and a plan for a fitted sample.
Start with a headboard photo or rough panel thickness. A full furniture drawing can follow later.
A lamp that looks neat on a bench can sit poorly on a finished headboard. VST supplies the mounting plate and protected lead with the light, so you can compare headboard reading light supplier quotes against the same installation scope.
Purchasing risk: The lamp can loosen or mark the upholstery.
Confirm: Backing material
VST solution direction: Specify fasteners through a sound insert.
Purchasing risk: The installed product appears unfinished.
Confirm: Rear cavity
VST solution direction: Move the feed through a protected rear exit.
Purchasing risk: Reading comfort falls despite adequate light.
Confirm: Bed geometry
VST solution direction: Set an aiming range around the intended reading area.
VST can adapt an existing head and plate at its headboard reading light factory when they fit the furniture section. If the recess, trim or reach limit rules them out, the bracket or aiming joint needs a new design.
Head shape, beam control and visible finish can follow the room design; the achieved beam is assessed on a mounted sample.
Buyer input: Reading position
Plate footprint, screw locations and backing interface can suit solid wood or an engineered insert.
Buyer input: Panel section
Arm length, pivot stop and switch position can be selected so the lamp is reachable without striking the headboard.
Buyer input: Reach envelope
Rear feed, strain relief and service access are chosen alongside the furniture cavity.
Buyer input: Access side
The choice changes the light position and the furniture clearance. Select the construction that fits the real headboard depth and bedside movement.
| Decision factor | Fixed Compact Head | Adjustable Reading Arm | Buyer guidance |
|---|---|---|---|
| Beam placement | Position set during installation | Reader can aim the head after installation | Use the expected pillow position to choose a useful reach. |
| Protrusion | Less movement into occupied space | Arm projects beyond the mounting plate | Measure the clear zone beside the sleeper. |
| Mechanical wear | Few moving interfaces | Joint and stops require retention checks | Specify the cycle and handling expected for the room. |
| Cleaning access | Simple fixed outline | More surfaces around the joint | Match the head shape to the maintenance routine. |
| Cable path | Shorter internal route | Flexible path through the moving assembly | Keep the lead protected at the pivot. |
With VST as the headboard reading light manufacturer, the panel section sets the backing, finished face and cable cavity. The mounting sketch fixes the plate and feed positions. A fitted sample shows whether the head reaches the reading position without striking the furniture.
VST work: Map the backing, finished surface and cable cavity.
Stage output: Mounting footprint and drilling sketch.
VST work: Seat the rear grommet and route the lead clear of fasteners.
Stage output: Protected cable path in the panel mock-up.
VST work: Set the head reach and pivot stop at the reading position.
Stage output: Mounted sample with an agreed aiming envelope.
VST work: Record finish, fasteners, cable and joint hardware.
Stage output: Assembly drawing and controlled parts list.
The headboard reading light supplier sample is checked at reading height, with the joint mounted in a representative panel. The photos illustrate the methods; actual readings belong in the sample test record.
Purpose: Assess useful light at the page.
Method: Measure on a book-sized target with the lamp mounted at headboard height.
Acceptance criteria: A target range is agreed for the actual bed layout.
Evidence: A lux map can accompany the selected sample.
Purpose: Verify the connected lamp runs as intended.
Method: Operate the sample from its specified supply and observe input and control function.
Acceptance criteria: The released circuit operates without wiring or switch faults.
Evidence: A function sheet can document the chosen circuit.
Purpose: Locate heat near the user and furniture.
Method: Operate the mounted lamp, then inspect the head and adjacent panel.
Acceptance criteria: Observed temperatures meet the chosen components and furniture limits.
Evidence: A temperature-point log follows an actual sample test.
Purpose: Check that aiming stays where it is set.
Method: Apply a controlled force to the unpowered head and inspect joint movement.
Acceptance criteria: The selected joint holds the intended reading angle.
Evidence: A retention observation can be recorded for the accepted joint.
The mounting sketch shows plate holes and rear feed. Any test observations belong to the agreed headboard sample.
Fixing points, plate outline and rear feed.
Supply, polarity and connection path for the selected version.
Only results actually obtained from the agreed headboard sample.
An existing headboard lamp with a light change usually starts at 500 units per model. If the project needs a new head, aiming joint or mounting construction, the usual starting quantity is 1,000 units for that model.
VST can make a mounted sample so you can judge the beam and plate on real furniture. Machining, sample work and any dedicated tooling may incur charges. Eligible sample costs can be credited against a later order if agreed.
Allow 15-25 working days for a lightly customized sample and 20-30 for production. A new construction typically needs 30-50 working days for samples and 25-35 for production once the design is set.
A plate die or aiming-joint tool may carry a separate charge for this model. Written order terms can specify the amount credited against a later headboard lamp order.
The head, joint, finish and cable are recorded under the released version, so repeat batches use the same construction. With a steady forecast, VST can reserve key materials ahead of future production.
The lamp can be packed with protective sleeves and individual cartons that suit furniture assembly. Labels and fitting instructions can carry the details needed for your market and installation sequence.
You may know the headboard finish before the internal panel construction is settled. The mounting insert must carry the lamp, while the cable and power interface need space behind the visible face. A photograph or rough panel section is enough for an initial discussion; the final fixing detail follows the furniture build.
Yes, when the mounting screws reach a solid insert behind the upholstery. The fabric itself should not carry the lamp load.
The electrical scope is fixed in the quote.
| Item | Order boundary |
|---|---|
| Lamp | Head, mount and attached lead |
| Power | Specified driver or host supply |
| Furniture | Backing and installation by the host build |
A front-service plate or an alternative feed can be considered, but the removable opening and cable path must be designed into the furniture.
The switch may be integrated at the plate, arm or host controls if the selected wiring and reachable position allow it.
Keep the released head, joint, finish, mounting pattern and connection details under one version reference.
